4th Edition

Photovoltaic Systems Engineering

By Roger A. Messenger, Amir Abtahi Copyright 2017
    536 Pages
    by CRC Press

    536 Pages
    by CRC Press

    The primary purpose of PV Systems Engineering is to provide a comprehensive set of PV knowledge and understanding tools for the design, installation, commissioning, inspection, and operation of PV systems. During recent years in the United States, more PV capacity was installed than any other electrical generation source. In addition to practical system information, this new edition includes explanation of the basic physical principles upon which the technology is based and a consideration of the environmental and economic impact of the technology. The material covers all phases of PV systems from basic sunlight parameters to system commissioning and simulation, as well as economic and environmental impact of PV. With homework problems included in each chapter and numerous design examples of real systems, the book provides the reader with consistent opportunities to apply the information to real-world scenarios.

    PrefaceDisclaimerAcknowledgmentsAuthorsAbbreviations Chapter 1: Background1.1 Introduction1.2 Population and Energy Demand1.3 Current World Energy Use Patterns1.4 Exponential Growth1.5 Hubbert’s Gaussian Model1.6 Net Energy, BTU Economics, and the Test for Sustainability1.7 Direct Conversion of Sunlight to Electricity with PV1.8 Energy UnitsReferencesSuggested ReadingChapter 2: The Sun2.1 Introduction2.2 The Solar Spectrum2.3 Effect of Atmosphere on Sunlight2.4 Sunlight Specifics2.5 Capturing SunlightReferencesSuggested ReadingChapter 3: Introduction to PV Systems3.1 Introduction3.2 The PV Cell3.3 The PV Module3.4 The PV Array3.5 Energy Storage3.6 PV System Loads3.7 PV System Availability: Traditional Concerns and New Concerns 3.8 Associated System Electronic Components 3.9 Generators3.10 Balance of System ComponentsReferences Suggested ReadingChapter 4: Grid-Connected Utility-Interactive Photovoltaic Systems4.1 Introduction4.2 Applicable Codes and Standards4.3 Design Considerations for Straight Grid-Connected PV Systems 4.4 Design of a System Based on Desired Annual System Performance4.5 Design of a System Based upon Available Roof Space4.6 Design of a Microinverter-Based System4.7 Design of a Nominal 20 kW System That Feeds a Three-Phase Distribution Panel4.8 Design of a Nominal 500-kW System 4.9 System Commissioning4.10 System Performance MonitoringReferences Suggested ReadingChapter 5: Mechanical Considerations5.1 Introduction5.2 Important Pr

    Biography

    Roger Messenger is professor emeritus of electrical engineering at Florida Atlantic University in Boca Raton, Florida. He earned a PhD in electrical engineering at the University of Minnesota and is a Registered Professional Engineer, a former Certified Electrical Contractor, and a former NABCEP Certified PV Installer. He has enjoyed working on field installations as much as he enjoys teaching classes or working on the design of a system or contemplating the theory of operation of a system or commissioning a system. His research work has ranged from electrical noise in gas discharge tubes to deep impurities in silicon to energy conservation to PV system design and performance. Dr. Messenger worked on the development and promulgation of the original Code for Energy Efficiency in Building Construction in Florida and has conducted extensive field studies of energy consumption and conservation in buildings and swimming pools. Since his retirement from Florida Atlantic University in 2005, he has worked as vice president for engineering at VB Engineering, Inc., in Boca Raton and as senior associate at FAE Consulting in Boca Raton. While at VB Engineering, he directed the design of several hundred PV designs, including the 5808-module, 4-acre, 1-MW system on the roof of the Orange County Convention Center in Orlando, Florida. While at FAE Consulting, he led the design of an additional 6 MW of systems that were installed. Dr. Messenger has also been active in the Florida Solar Energy Industries Association and the Florida Alliance for Renewable Energy, has served as a peer reviewer for the U.S. Department of Energy, and has served on the Florida Solar Energy Center Advisory Board. He has conducted numerous seminars and webinars on designing, installing, and inspecting PV systems.





    Homayoon "Amir" Abtahi is an associate professor of mechanical engineering at Florida Atlantic University. He earned a PhD in mechanical engineering from the Massachusetts Institute of Technology in 1981 and joined Florida Atlantic University in 1983. In addition to his academic activity, he has a wealth of practical experience, much of which has been obtained as a volunteer. He is a Registered Professional Engineer in Florida and a member of ASME, IEEE, ASHRAE, and SAE. Dr. Abtahi has held LEED Certification since 2007, is ESTIDAMA Certified in the United Arab Emirates, and is a Certified General Contractor and a Certified Solar Contractor in the state of Florida. His interests range widely from PV to PEM fuel cells, integrated capacitor/battery power modules, and atmospheric water generation. In 1985, he installed the first solar-power system in Venezuela and was responsible for the first application of solar power for post-hurricane emergency power and lighting and Ham radio communication operations in the aftermath of Hurricane Hugo in St. Croix in 1989 and Hurricane Marilyn in St. Thomas in 1995. In 1989, Dr. Abtahi published the first comprehensive catalog of 12-V appliances for use with PV systems. Recently, he has been involved with PV installations in the Caribbean, South America, Bangladesh, and India. From 2008 to 2010, he was responsible for design and installation of over 100 residential and 20 commercial/industrial PV systems. Over the past 15 years, he has had responsibility for the design and installation of 1 million BTUD of solar hot water and solar process heat. Along with PV and thermal applications, he has had experience with heat exchangers, MEP plan review, LEED projects, tracking PV, micro-turbines, parabolic trough solar, and other hybrid applications.

    "The new edition of the text represents an outstanding improvement over earlier versions. I would highly recommend it to any faculty interested in teaching a course related to photovoltaic systems engineering for the following reasons: a) It represents an excellent balance of theory and practical engineering application of science, technology, and economic analysis; b) It is up-to-date on the latest technology, system components, codes and standards, and accepted design practices, c) The problem sets at the end of each chapter are well thought out and provide students with relevant needed practice necessary for developing comprehensive design knowledge and skills for a variety of PV system configurations; d) The book is extremely well organized, well written, easy to follow, and should appeal to a large segment of both student and practicing engineering populations. In short, it is an excellent engineering text on extremely important subject matter from which faculty will enjoy teaching and from which student learning will be enhanced."
    Jerry Ventre, Florida Solar Energy Center (Retired), USA

    "This book, now in its 4th edition, is thorough, comprehensive and frequently revised, so it is up-to-date. I have always liked it, in earlier editions, for bothering to address the low profile but important aspects of photovoltaic systems that tend to be left out of other books – the mechanical engineering aspects, including mounting methods, loads and stresses and wind loading; electrical protection; standards (for USA at least); wire sizing; junction boxes; environmental impacts, etc."
    — Richard Corkish, University of New South Wales, Australia

     

    "I find this book to be excellent, containing both the theoretical and practical knowledge to analyze and design a wide range of solar photovoltaic systems. I am not aware of any currently available books that include such breadth and depth."
    — John Murray, Dine Colleg